GEt Quote
  • Reading a Screw Specification: L/D, Compression Ratio, Speed

    Nov 15, 2026 | ACS MATERIAL LLC

    An extruder page usually prints three screw numbers: the length-to-diameter ratio, the compression ratio and the screw speed. Each is useful, and each is easy to over-read. This guide explains what each number describes, what it cannot tell you, how to ask for the missing context, and what the figures on four Polytevo Series by ACS Material pages actually say.

    Terms used in this guide. L/D is the ratio of screw length to screw diameter. Compression ratio describes how much the screw channel is reduced between the feed end and the metering end; the exact definition varies and has to be stated with the number. Specific mechanical energy (SME) is the mechanical energy put into the material per unit mass, commonly in kWh/kg.
    Close-up of a bare extruder screw lying on a bench beside a split barrel, with the flights in focus
    A screw is described by more than three numbers; these three are where to start.

    1.  What a screw specification is, and is not

    A screw specification is a short description of a long geometry. The three numbers on most extruder pages, the L/D, the compression ratio and the screw speed, say how long the screw is for its diameter, how much the channel narrows along it and how fast it turns. They do not say how deep the channel is at any point, how the flights or mixing elements are arranged, or how much material the machine will deliver, which are the things that decide what the screw does to a material. Use the numbers to frame questions rather than to rank machines.

    This guide takes the three numbers in turn in sections 2 to 4, shows the figures four Polytevo pages publish in section 5 without drawing a ranking from them, and in section 6 turns the discussion into a short list of questions to ask about any screw. The cluster entry point, How to Choose a Laboratory Extruder: Types, Scale and Duty, explains where a screw specification sits in the larger decision, and Single-Screw vs Twin-Screw Extruders: Which One for a Lab? covers how the answer changes between single-screw and twin-screw machines.

    2.  L/D: length relative to diameter

    L/D relates a specified processing length to a nominal screw diameter. Confirm the definition used for the quoted value; do not substitute overall shaft length. In an illustrative case, a 20 mm diameter and L/D of 25 imply 500 mm for the length used in that definition. A hot-melt-extrusion review gives the same kind of example, a 1000 mm length with a 25 mm screw diameter as 40:1.1

    What a longer screw offers is distance along which conveying, melting and mixing can take place; the review describes the length assigned to each operation as depending on the barrel L/D.1 The plasticating model of a single-screw extruder, for example, predicts how temperature, pressure and the solids content change along the whole length of the machine, which is why the length is part of the description.2 That is all the ratio says. Whether the extra length produces more melting, more mixing or a longer time at temperature depends on the screw design and the operating point, and an instrumented laboratory single-screw extruder was built to study how screw geometry and operating conditions affect the plasticating sequence along the screw.3

    Two practical consequences follow. First, L/D is comparable between screws of the same family and purpose and much less so across families: a single-screw melting-and-pumping screw and a modular twin-screw compounding screw are built for different jobs, so two ratios from different families do not rank the machines. Second, L/D alone does not determine output. Output depends on the feed, the screw geometry, the speed and the material, which is why an hourly figure on a page is a figure with conditions.1

    3.  Compression ratio: how the channel narrows

    A conventional three-zone compression screw has a deeper feed channel and a shallower metering channel; the compression ratio compares the two.1,4 A quoted compression ratio must identify the sections and whether the ratio is defined using channel depth or channel volume. One technical article describes it as the ratio of the volumes of the first and last flights, which in constant-pitch screws becomes the ratio of the two channel depths.5 Do not assume that one definition or geometry applies to every screw. The ratio is one of the ways a screw’s geometry is described, and the screw geometry is part of how the conveying and melting sequence develops.2

    A barrier screw is a different geometry that separates solid and melt in the channel. In the instrumented laboratory single-screw study, conventional and barrier profiles were compared for their effect on the evolution of the plasticating sequence of a low-density polyethylene.3 That study is one reason not to treat the compression ratio as a complete description: two screws with the same ratio can still differ in design. In the twin-screw review the screws are typically segmented and assembled on shafts;6 a screw built from separate elements may not have a single compression ratio, and a page may not print one.

    4.  Screw speed, throughput and energy input

    Screw speed is rotational speed, not throughput or material velocity along the barrel. In metered, starve-fed operation, feed rate and screw speed can be controlled separately within the machine’s conveying capacity.1,6 Their combination, screw geometry and downstream restrictions affect filling and material transport. In the distributive-mixing study cited below, fill and local average residence time were related to mixing in conveying sections.7

    A study of polycarbonate/carbon nanotube composites on a laboratory twin-screw extruder varied screw design, rotation speed, throughput, feeding position and filler content, and found that the dispersion correlated with the specific mechanical energy applied, with no further improvement above about 0.4 kWh/kg.8 The speed alone did not describe the result, and the same study shortened the nanotubes as the energy rose. A residence-time study on a 30 mm co-rotating twin-screw extruder found that operating conditions with equivalent specific throughput gave an equivalent residence-volume and residence-revolution distribution.9 Both studies point to the same practice: report the screw speed together with the feed rate, because neither number alone describes the run.

    A speed range on a page is therefore a capability, not a recommendation. A page that lists a range such as 0.1 to 100 rpm is describing what the drive can do; it does not say what the right speed is for a given material, nor what output that speed will deliver.

    5.  What four Polytevo pages publish

    This section reports what four Polytevo pages say on 15 November 2026. No literature appears in it, and the earlier sections are not claims about these machines.

    Polytevo pageScrew diameter as publishedL/D as publishedScrew speed as published
    Single Screw Extruder20 mm or 30 mm28:10.1–100 rpm (20 mm version)
    Benchtop Single-Screw Extruder16 mm14:1Rated 0.1–20 rpm
    Benchtop Mini Extruder20 mm9:11–150 rpm (servo motor)
    Twin-Screw Extrusion and Pelletizing LineØ22 mm; co-rotating twin screws42:1Maximum screw speed 600 rpm

    Figures are copied from the pages and keep each page’s own labels; the order of the rows is not a ranking.

    The Polytevo Series Single Screw Extruder page also publishes a compression ratio of 2.4:1 for both screw versions, and the Polytevo Series Benchtop Single-Screw Extruder page a compression ratio of 3:1. The supplied configuration is confirmed on quotation, which is the place to ask how the ratio is defined.

    The Polytevo Series Benchtop Mini Extruder page describes a laboratory benchtop extrusion molding system, so its screw figures belong to an extruder that is part of a combined system; the Polytevo Series Twin-Screw Extrusion and Pelletizing Line page describes a co-rotating twin-screw extruder with a modular screw and barrel. The two rows are therefore different kinds of machine, and this guide does not compare their L/D values as if they were the same kind of screw.

    6.  A reading checklist for any screw

    The table summarizes this guide as questions. It is working guidance from this guide, not a published rule.

    NumberWhat it describesWhat it cannot tell youAsk
    L/DScrew length relative to diameterOutput (L/D alone does not determine output), residence time or mixing qualityWhich length does the ratio use, and is it the processing length of the definition rather than the overall shaft length?
    Compression ratioHow much the channel narrows from the feed end to the metering endWhether the screw is a barrier or a mixing design, or how the material meltsHow is the ratio defined, by depth or by volume, and is it printed for every screw version?
    Screw speedHow fast the screw turns, usually as a rangeThe right speed for a material, or the throughput at that speedAt which speeds and feed rates were any output figures obtained?
    ThroughputMass delivered per unit time, usually with stated conditionsWhether the figure is a rated maximum, a typical value or a per-cycle massWhat do the stated conditions include, and is the figure for the screw or for the whole line?
    Specific mechanical energyMechanical energy per mass of materialWhere along the screw the energy was appliedWhat torque or power, speed, mass-flow and correction basis were used?

    Do not infer unpublished performance or combine quantities whose definitions or operating conditions are incompatible. A derived geometric or operating ratio can be useful when its inputs are defined and compatible, but label it as a calculation rather than a page-stated specification. Ask for clarification when an input’s meaning is uncertain.

    7.  Before you request a quote

    For a configuration discussion, describe the job and the screw questions you need answered:

    • the material and its form, and the polymer family;
    • the duty: melting and shaping, or compounding a filler or second polymer;
    • the quantity per run and in total;
    • any screw detail you need confirmed, such as the length the L/D refers to or the definition of the compression ratio;
    • the form of output you want.

    8.  FAQ

    What does an L/D of 28:1 mean?

    It means the processing length used in the definition is 28 times the nominal screw diameter. Confirm the definition used for the quoted value; do not substitute overall shaft length. L/D alone does not determine output or the quality of mixing.1

    Is a higher L/D always better?

    No. A longer screw offers more distance for conveying, melting and mixing, but what it delivers depends on the screw design and the operating point, not on the ratio alone.3

    What compression ratio do the Polytevo single-screw pages publish?

    The Polytevo Series Single Screw Extruder page publishes 2.4:1 for both screw versions, and the Polytevo Series Benchtop Single-Screw Extruder page publishes 3:1.

    Does the screw speed tell me the output of the extruder?

    No. Screw speed is rotational speed, not throughput. The output depends on the feed, the screw geometry and the material. A study on a laboratory twin-screw extruder found that the specific mechanical energy applied, not speed alone, correlated with the dispersion achieved.8

    What speed range does the Polytevo benchtop single-screw page publish?

    The Polytevo Series Benchtop Single-Screw Extruder page publishes a rated screw speed of 0.1–20 rpm.

    9.  Keep exploring the Lab-Scale Polymer Processing Knowledge Hub

    This guide belongs to the extruder cluster of the Lab-Scale Polymer Processing and Testing: A Workflow Guide, which places every machine of the Polytevo Series by ACS Material in the stage of the lab route where it is used. The cluster starts at How to Choose a Laboratory Extruder: Types, Scale and Duty; related guides in the cluster:

    To discuss a configuration, describe the material and its form, the sample quantity you need to process, whether the run is a batch or continuous, and the form of output you want, then send it through Request a Quote. Specifications are as published on each product page, and final configurations are confirmed on quotation.

    Disclaimer: This guide provides general educational information and a dated summary of the cited product pages. ACS Material makes no representations or warranties, either express or implied, regarding the suitability of any Polytevo Series product for any particular purpose or the accuracy of the information listed here. Product statements are those published on the Polytevo Series product pages on 15 November 2026; specifications are as published on each page and final configurations are confirmed on quotation. The explanations and examples in this guide are general guidance, not process recipes, and they contain no measured results. Literature statements are those of the cited authors and were not produced with Polytevo Series equipment unless the source says so. Always follow the product documentation and your laboratory’s safety procedures.

    10.  References

    1Patil H, Tiwari RV, Repka MA. Hot-melt extrusion: from theory to application in pharmaceutical formulation. AAPS PharmSciTech. 2016;17(1):20–42. DOI: Source record
    2Tadmor Z, Klein I. The formulation of a mathematical model for plasticating screw extrusion. Rubber Chem Technol. 1969;42(3):780–789. DOI: Source record
    3Gaspar-Cunha A, Carneiro OS, Cunha SM, Covas JA. Laboratory modular instrumented single screw extruder for optimisation of polymer processing. Plast Rubber Compos. 2012;41(9):373–383. DOI: Source record
    4Maniruzzaman M, Boateng JS, Snowden MJ, Douroumis D. A review of hot-melt extrusion: process technology to pharmaceutical products. ISRN Pharm. 2012;2012:436763. DOI: Source record
    5Griff A. Naming screws for materials, compression ratios and other ways to avoid dealing with real dimensions. SPE Extrusion Division Consultants’ Corner. 1995;22(1). Source record
    6Martin C. Twin screw extruders as continuous mixers for thermal processing: a technical and historical perspective. AAPS PharmSciTech. 2016;17(1):3–19. DOI: Source record
    7Shearer GC, Tzoganakis C. Relationship between local residence time and distributive mixing in sections of a twin-screw extruder. Polym Eng Sci. 2001;41(12):2206–2215. DOI: Source record
    8Pötschke P, Villmow T, Krause B, Kretzschmar B. Influence of twin screw extrusion conditions on MWCNT length and dispersion and resulting electrical and mechanical properties of polycarbonate composites. Polymers. 2024;16(19):2694. DOI: Source record
    9Gao J, Walsh GC, Bigio D, Briber RM, Wetzel MD. Residence-time distribution model for twin-screw extruders. AIChE J. 1999;45(12):2541–2549. DOI: Source record

    Further reading (not cited as evidence for any statement above)

    R1Rauwendaal C. Polymer Extrusion. 5th ed. Hanser; 2014. DOI: Source record
    R2Rauwendaal C. Extruder screw design. In: Polymer Extrusion. 5th ed. Hanser; 2014. p. 509–652. DOI: Source record
    R3Chung CI. Extrusion of Polymers. Hanser; 2019. DOI: Source record
    R4Kohlgrüber K, ed. Co-Rotating Twin-Screw Extruders: Fundamentals. Hanser; 2019. DOI: Source record